开云平台官方入口

标题: 壳牌石油公司 --油气分离器Gas Liquid Separators - Type Selection and Design Rules [打印本页]

作者: wdyou 时间: 2017-2-3 18:27
标题: 壳牌石油公司 --油气分离器Gas Liquid Separators - Type Selection and Design Rules
壳牌石油公司 --油气分离器Gas Liquid Separators - Type Selection and Design Rules，非常好的资料，英文版的，需要的快下载

1. INTRODUCTION
      1.1 SCOPE
      1.2 SUMMARY OF CHANGES SINCE PREVIOUS EDITION
      1.3 DISTRIBUTION, INTENDED USE AND REGULATORY CONSIDERATIONS
      1.4 DEFINITIONS
      1.5 CROSS-REFERENCES
      1.6 SYMBOLS AND ABBREVIATIONS
2. SELECTION CRITERIA FOR GAS/LIQUID SEPARATORS
      2.1 DUTY
      2.2 ORIENTATION
      2.3 COMPONENTS
      2.4 DESIGN BASE
      2.5 SELECTION STRATEGY
3. DESIGN RULES
      3.1 VERTICAL KNOCK-OUT DRUM
      3.2 HORIZONTAL KNOCK-OUT DRUM
      3.3 VERTICAL WIREMESH DEMISTER
      3.4 HORIZONTAL WIREMESH DEMISTER
      3.5 VERTICAL VANE-TYPE DEMISTER
      3.6 HORIZONTAL VANE-TYPE DEMISTER
      3.7 VERTICAL SEPARATOR WITH SWIRLTUBE DEMISTER DECK
      3.8 CYCLONE WITH TANGENTIAL INLET (CONVENTIONAL CYCLONE)
      3.9 CYCLONE WITH STRAIGHT INLET AND SWIRLER ("GASUNIE" CYCLONE)
      3.10 VERTICAL SEPARATOR WITH REVERSED-FLOW MULTICYCLONE BUNDLE (CONVENTIONAL MULTICYCLONE)
      3.11 VERTICAL SEPARATOR WITH AXIAL-FLOW MULTICYCLONE BUNDLE (WITH RECIRCULATION OF SECONDARY GAS)
      3.12 HORIZONTAL SEPARATOR WITH AXIAL-FLOW MULTICYCLONE BUNDLE (WITH RECIRCULATION OF SECONDARY GAS)
      3.13 FILTER SEPARATOR
4. PIPING REQUIREMENTS
5. REFERENCES

壳牌石油公司 --油气分离器Gas Liquid Separators - Type Selection and Design Rules.pdf

785.5 KB, 下载次数: 77

售价: 15 金币 [记录]

作者: helloshigy 时间: 2017-2-4 08:30
PREFACE

They are based on the experience acquired during their involvement with the design, construction, operation and
maintenance of processing units and facilities, and they are supplemented with the experience of Group Operating
companies. Where appropriate they are based on, or reference is made to, international, regional, national and industry
standards.
The objective is to set the recommended standard for good design and engineering practice applied by Group
companies operating an oil refinery, gas handling installation, chemical plant, oil and gas production facility, or any other
such facility, and thereby to achieve maximum technical and economic benefit from standardization.
The information set forth in these publications is provided to users for their consideration and decision to implement.
This is of particular importance where DEPs may not cover every requirement or diversity of condition at each locality.
The system of DEPs is expected to be sufficiently flexible to allow individual operating companies to adapt the
information set forth in DEPs to their own environment and requirements.
When Contractors or Manufacturers/Suppliers use DEPs they shall be solely responsible for the quality of work and the
attainment of the required design and engineering standards. In particular, for those requirements not specifically
covered, the Principal will expect them to follow those design and engineering practices which will achieve the same
level of integrity as reflected in the DEPs. If in doubt, the Contractor or Manufacturer/Supplier shall, without detracting
from his own responsibility, consult the Principal or its technical advisor.

作者: helloshigy 时间: 2017-2-4 08:31
APPENDICES
APPENDIX I NATURE OF THE FEED .................................................................................80
APPENDIX II SIZING OF THE FEED AND OUTLET NOZZLES ..........................................84
APPENDIX III DESIGN OF SCHOEPENTOETER (VANE-TYPE) INLET DEVICE ...............86
APPENDIX IV DESIGN MARGINS FOR SEPARATOR DESIGN ..........................................91
APPENDIX V LEVEL CONTROL...........................................................................................92
APPENDIX VI VESSEL GEOMETRICAL RELATIONSHIPS..................................................94
APPENDIX VII SIZING OF SEPARATOR VESSELS..............................................................98
APPENDIX VIII MISTMAT SPECIFICATIONS .......................................................................103
APPENDIX IX VANE PACKS................................................................................................104
APPENDIX X VESSEL SIZING EXAMPLES .......................................................................106
APPENDIX XI DEBOTTLENECKING TIPS ..........................................................................113

作者: helloshigy 时间: 2017-2-4 08:54
我给你加了内容以后最好把目录和一些文章内容写到帖子里这样大家可看看根据需要下载

作者: wdyou 时间: 2017-2-4 11:21

helloshigy 发表于 2017-2-4 08:54
我给你加了内容以后最好把目录和一些文章内容写到帖子里这样大家可看看根据需要下载

谢谢...........

作者: tony802106 时间: 2017-2-4 11:30
不知道是否详细，感觉12J里太粗略了。。。

作者: wdyou 时间: 2017-2-4 14:17

tony802106 发表于 2017-2-4 11:30
不知道是否详细，感觉12J里太粗略了。。。

还好，多结合几个标准看看就好了，我感觉比那个20570要好多了

作者: cosn 时间: 2017-2-5 21:01
十几年前的资料，希望还没有过时，英文的看起来耗时。

作者: wdyou 时间: 2017-2-6 09:54

cosn 发表于 2017-2-5 21:01
十几年前的资料，希望还没有过时，英文的看起来耗时。

就是因为10几年前的才珍贵，不懂别乱说

作者: tomlu 时间: 2017-3-16 16:10
已经有新版的了

作者: yujian_12 时间: 2017-3-21 23:15
这是壳牌的DEP吗？最新的版本是41版了。

作者: wdyou 时间: 2017-3-22 13:46

yujian_12 发表于 2017-3-21 23:15
这是壳牌的DEP吗？最新的版本是41版了。

把你的41版发来看看

作者: swl83 时间: 2018-3-6 09:11
价格好高呀，能发我一份么？呵呵

作者: swl83 时间: 2018-3-6 09:36
新版的能上传来看看么

作者: zl0811000 时间: 2020-3-7 10:25
谢谢楼主分享

作者: 911maker 时间: 2020-3-12 23:25
一个个都好牛，玩全英文的{:4_92:}

作者: zccrg002 时间: 2020-3-14 09:22
谢谢楼主的分享。

欢迎光临开云平台官方入口 (//m.pifpin.com/)

map